Advanced VESA Mounting Plate: Compatibility and Installation Guide

Quick answer

Match the VESA pattern and weight of your monitor to the plate and stand, mount the plate to the monitor first, then attach it to the rig and adjust alignment before final tightening. If your monitor or stand specs are not listed, treat that as a decision limitation and confirm with the manufacturer before buying.

Getting a monitor onto a sim rig is less about strength and more about matching the right pattern, then working in the right order. A VESA mounting plate is the interface between your display and the stand, so a mismatch there affects everything above it.

This guide walks through compatibility checks and a clean installation sequence for a sim racing monitor mount. It uses plain steps and checkpoints, including where a small accessory like the Advanced Hook can keep your headset or cables off the rig while you work.

Check VESA pattern and weight before you buy

Find the VESA pattern on your monitor, usually listed as horizontal and vertical hole spacing in millimeters, such as 75 x 75 or 100 x 100. Then compare it to the plate and the stand's supported pattern. If either side does not list a pattern, do not assume it fits; confirm with the seller or manufacturer.

Weight and size matter as much as hole spacing. A plate rated for a small display may flex under a larger one, and a stand may not hold a heavy monitor at full extension. Keep the monitor within the stand's stated limits and check that the plate's hardware matches the thread size on your display.

• Measure hole spacing yourself if the manual is missing; do not rely on the box image.
• Confirm screw length so bolts do not bottom out inside the monitor housing.

Prepare the rig and protect the display

Work on a stable surface with the monitor face down on a soft cloth, and keep the stand or rig upright nearby. Lay out the plate, screws, washers, and any spacers so you can see the correct count before you start. This prevents cross-threading and lost hardware.

If your rig uses aluminum profile, have T-nuts and the right hex keys within reach. A small accessory such as the Advanced Hook can hold a headset or cable out of the way, but keep the work area clear first so nothing falls onto the screen.

• Do not fully tighten any bolt until all four are started by hand.
• Keep magnetic tools away from the monitor panel and cables.

Install the plate on the monitor, then the rig

Attach the VESA plate to the back of the monitor using the correct screws and any required spacers. Start all screws by hand, then snug them in a cross pattern so the plate sits flat. Once the plate is secure, lift the monitor with a second person if it is large, and attach the plate to the stand or rig mount.

For a sim racing monitor mount, position the display at eye level and slightly behind the wheelbase if your stand allows it. Tighten the stand's adjustment points only after you confirm the screen is centered and level. Recheck screw torque after the first session, since vibration can loosen hardware.

• Use a level app or a small bubble level on the top edge before final tightening.
• If the plate or stand has slotted holes, use them for fine alignment rather than forcing the frame.

Step-by-step VESA plate installation

1. Confirm VESA pattern and weight limits: Measure the hole spacing on the monitor and compare it to the plate and stand specifications. Check the monitor weight against the stand's limit. Checkpoint: if any specification is missing, pause and confirm before buying or drilling.
2. Gather hardware and protect the screen: Lay the monitor face down on a soft cloth and sort screws, washers, and spacers. Keep T-nuts and hex keys ready for aluminum profile. Checkpoint: start every screw by hand to avoid cross-threading.
3. Attach the plate to the monitor: Fit the VESA plate to the monitor back, using spacers if the housing requires them. Tighten in a cross pattern until the plate sits flat. Checkpoint: the plate should not rock or contact the monitor housing unevenly.
4. Mount the plate to the stand or rig: With help for larger displays, lift the monitor and attach the plate to the stand or rig mount. Leave the stand adjustments loose enough to move the screen. Checkpoint: keep the monitor supported until at least two bolts are snug.
5. Align, level, and tighten: Set the screen at eye level and centered behind the wheelbase. Level the top edge, then tighten all adjustment points and VESA bolts. Checkpoint: recheck torque after your first driving session.

Product facts that help with mounting

• Advanced Hook: Steel hook with two M8 screws and matching T-nuts for mounting to an Advanced SimRacing-brand chassis; supports headphones or a VR headset. Keeps a headset or cables off the rig while you install and adjust the monitor, reducing clutter around the mounting area.
• Advanced Pivoting Side Arm: Mounts additional equipment such as a flight simulation throttle on the left or right side and creates a pivoting gate for easier seat access; compatible with ASR 1, 3, 4, 6 and PRO, but not the ASR F line-up. Shows how side-mounted accessories can share the same profile as a monitor stand, so plan hole usage before adding a VESA plate.
• Simucube Shaft Extension Kit [SC3]: Adjustable shaft extensions in 100 mm or 200 mm options improve immersion and ergonomics and let you position the monitor lower and closer to eye level while retaining wireless functionality; do not combine multiple extensions, and extending over 200 mm may damage the wheelbase. Explains why monitor height and distance are usually adjusted at the stand or shaft, not by forcing the VESA plate beyond its intended range.

A clean VESA installation comes down to confirming the pattern and weight, mounting the plate to the monitor first, and aligning before you tighten. If your monitor or stand specs are not published, treat that as a limitation and verify with the manufacturer rather than guessing.